{"title":"Copper Rivet Belt Fastener Kits","description":"\u003cp\u003eMATO Copper Rivet fastener kits (CR-Super, CR-2A) for agricultural balers, flat belt power transmission, grain elevators, and non-sparking applications. 24\" and 72\" kit sizes, steel-copper and stainless-copper combinations.\u003c\/p\u003e","products":[{"product_id":"copper-rivet-fastener-cr-2as-36-copper-rivet-36-ss","title":"Copper Rivet CR-2A Complete Splice Kit - 316 Stainless Fasteners with Copper Rivets, 36\" (900mm) Belt Width","description":"\u003cp\u003e\u003cstrong\u003eCopper Rivet CR-2A Complete Splice Kit\u003c\/strong\u003e is a stainless fastener and copper rivet belt splicing kit for a 36-inch (900mm) belt width. The kit contains matched fastener strips, solid copper rivets, copper burrs (washers), and installation instructions for a permanent clinched mechanical splice. CR-2A is MATO's light-duty copper rivet kit sized for smaller agricultural and industrial belts in the 12\" to 36\" width range.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is in the package:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMatched fastener strips\u003c\/strong\u003e (stainless steel) sized for 36\" (900mm) belt\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolid copper rivets\u003c\/strong\u003e (corrosion-resistant, non-sparking)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCopper burrs (washers)\u003c\/strong\u003e for distributing clinching load\u003c\/li\u003e\n\u003cli\u003eInstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eRequired installation hardware NOT included:\u003c\/strong\u003e rivet setter or punch, hammer, backing anvil, belt cutter or square. Sold separately.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy copper:\u003c\/strong\u003e Copper is naturally corrosion-resistant, clinches cleanly on fabric and rubber carcasses without cracking, and is non-sparking. This makes it the traditional and current choice for grain elevators, flour mills, and environments where ferrous sparks are unacceptable near dry crops or combustible dust. Copper burrs distribute clinching load across the belt surface, maintaining grip even on soft or worn belt covers.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMaterial combination:\u003c\/strong\u003e 316 stainless steel fastener strips paired with solid copper rivets and copper burrs. Stainless fastener with copper rivets combines corrosion resistance with non-sparking behavior for the most demanding wash-down and dust-hazard applications.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eApplications:\u003c\/strong\u003e Used in smaller baler belts, forage harvester belts, farm-equipment drive belts, flour mill conveyors requiring non-sparking hardware, and small-belt power transmission repair. Not recommended for heavy mining, quarry, cement, or high-PIW conveyors where Plategrip or Riv-Nail is the correct choice.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInstallation:\u003c\/strong\u003e Requires a rivet setter or punch, hammer, backing anvil, belt cutter or square, and optionally a rivet-setting press. Skill level is moderate. Technicians match rivet length to combined belt thickness plus burr, maintain consistent hole spacing, and avoid over-peening that would crack the burr or deform the belt.\u003c\/p\u003e\u003cp\u003eTexas Belting is an authorized MATO distributor shipping from Houston, TX. Same-day shipping on stocked items. Call 888-203-2358 for sizing help or bulk pricing.\u003c\/p\u003e","brand":"MATO","offers":[{"title":"Default Title","offer_id":46693268652221,"sku":"CR-2AS-36","price":432.33,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0666\/7721\/files\/cai-riv-nail-rivets-group_2da70e03-cd6e-4047-a48f-04ec7d79168a.jpg?v=1778107146"},{"product_id":"copper-rivet-fastener-cr-2as-20-copper-rivet-20-ss","title":"Copper Rivet CR-2A Complete Splice Kit - 316 Stainless Fasteners with Copper Rivets, 20\" (500mm) Belt Width","description":"\u003cp\u003e\u003cstrong\u003eCopper Rivet CR-2A Complete Splice Kit\u003c\/strong\u003e is a stainless fastener and copper rivet belt splicing kit for a 20-inch (500mm) belt width. The kit contains matched fastener strips, solid copper rivets, copper burrs (washers), and installation instructions for a permanent clinched mechanical splice. CR-2A is MATO's light-duty copper rivet kit sized for smaller agricultural and industrial belts in the 12\" to 36\" width range.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is in the package:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMatched fastener strips\u003c\/strong\u003e (stainless steel) sized for 20\" (500mm) belt\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolid copper rivets\u003c\/strong\u003e (corrosion-resistant, non-sparking)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCopper burrs (washers)\u003c\/strong\u003e for distributing clinching load\u003c\/li\u003e\n\u003cli\u003eInstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eRequired installation hardware NOT included:\u003c\/strong\u003e rivet setter or punch, hammer, backing anvil, belt cutter or square. Sold separately.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy copper:\u003c\/strong\u003e Copper is naturally corrosion-resistant, clinches cleanly on fabric and rubber carcasses without cracking, and is non-sparking. This makes it the traditional and current choice for grain elevators, flour mills, and environments where ferrous sparks are unacceptable near dry crops or combustible dust. Copper burrs distribute clinching load across the belt surface, maintaining grip even on soft or worn belt covers.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMaterial combination:\u003c\/strong\u003e 316 stainless steel fastener strips paired with solid copper rivets and copper burrs. Stainless fastener with copper rivets combines corrosion resistance with non-sparking behavior for the most demanding wash-down and dust-hazard applications.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eApplications:\u003c\/strong\u003e Used in smaller baler belts, forage harvester belts, farm-equipment drive belts, flour mill conveyors requiring non-sparking hardware, and small-belt power transmission repair. Not recommended for heavy mining, quarry, cement, or high-PIW conveyors where Plategrip or Riv-Nail is the correct choice.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInstallation:\u003c\/strong\u003e Requires a rivet setter or punch, hammer, backing anvil, belt cutter or square, and optionally a rivet-setting press. Skill level is moderate. Technicians match rivet length to combined belt thickness plus burr, maintain consistent hole spacing, and avoid over-peening that would crack the burr or deform the belt.\u003c\/p\u003e\u003cp\u003eTexas Belting is an authorized MATO distributor shipping from Houston, TX. Same-day shipping on stocked items. Call 888-203-2358 for sizing help or bulk pricing.\u003c\/p\u003e","brand":"MATO","offers":[{"title":"Default Title","offer_id":46693268979901,"sku":"CR-2AS-20","price":192.14,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0666\/7721\/files\/cai-riv-nail-rivets-group_264456d7-63ee-4fce-a31e-57499c117f5d.jpg?v=1778107145"},{"product_id":"copper-rivet-fastener-cr-super-a-72-stl-w-copper-rivets","title":"Copper Rivet CR-Super Complete Splice Kit - Steel Fasteners with Copper Rivets, 72\" (1800mm) Belt Width","description":"\u003cp\u003e\u003cstrong\u003eCopper Rivet CR-Super Complete Splice Kit\u003c\/strong\u003e is a steel fastener and copper rivet belt splicing kit for a 72-inch (1800mm) belt width. The kit contains matched fastener strips, solid copper rivets, copper burrs (washers), and installation instructions for a permanent clinched mechanical splice. CR-Super is MATO's primary copper rivet splice kit for rubber-and-fabric baler belts, canvas flat belts, and fabric-reinforced power transmission belts.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is in the package:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMatched fastener strips\u003c\/strong\u003e (carbon steel) sized for 72\" (1800mm) belt\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolid copper rivets\u003c\/strong\u003e (corrosion-resistant, non-sparking)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCopper burrs (washers)\u003c\/strong\u003e for distributing clinching load\u003c\/li\u003e\n\u003cli\u003eInstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eRequired installation hardware NOT included:\u003c\/strong\u003e rivet setter or punch, hammer, backing anvil, belt cutter or square. Sold separately.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy copper:\u003c\/strong\u003e Copper is naturally corrosion-resistant, clinches cleanly on fabric and rubber carcasses without cracking, and is non-sparking. This makes it the traditional and current choice for grain elevators, flour mills, and environments where ferrous sparks are unacceptable near dry crops or combustible dust. Copper burrs distribute clinching load across the belt surface, maintaining grip even on soft or worn belt covers.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMaterial combination:\u003c\/strong\u003e Steel fastener strips paired with solid copper rivets and copper burrs. Steel fastener with copper rivets is the standard economical combination for general agricultural and industrial service.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eApplications:\u003c\/strong\u003e Used in round-baler belt splicing on John Deere, New Holland, and Vermeer equipment, grain elevator transfer belts, sawmill flat drive belt repair, and legacy power transmission applications. Not recommended for heavy mining, quarry, cement, or high-PIW conveyors where Plategrip or Riv-Nail is the correct choice.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInstallation:\u003c\/strong\u003e Requires a rivet setter or punch, hammer, backing anvil, belt cutter or square, and optionally a rivet-setting press. Skill level is moderate. Technicians match rivet length to combined belt thickness plus burr, maintain consistent hole spacing, and avoid over-peening that would crack the burr or deform the belt.\u003c\/p\u003e\u003cp\u003eTexas Belting is an authorized MATO distributor shipping from Houston, TX. Same-day shipping on stocked items. Call 888-203-2358 for sizing help or bulk pricing.\u003c\/p\u003e","brand":"MATO","offers":[{"title":"Default Title","offer_id":46693269110973,"sku":"CR-Super A-72","price":452.97,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0666\/7721\/files\/cai-riv-nail-rivets-group_9343821b-fd20-44a4-9f86-e46c2e934ece.jpg?v=1778107145"},{"product_id":"copper-rivet-fastener-cr-ams-54-ss-fastener-set","title":"Copper Rivet CR-AMS Complete Splice Kit - 316 Stainless Fasteners with Copper Rivets, 54\" (1350mm) Belt Width","description":"\u003cp\u003e\u003cstrong\u003eCopper Rivet CR-AMS Complete Splice Kit\u003c\/strong\u003e is a stainless fastener and copper rivet belt splicing kit for a 54-inch (1350mm) belt width. The kit contains matched fastener strips, solid copper rivets, copper burrs (washers), and installation instructions for a permanent clinched mechanical splice. CR-AMS is MATO's stainless-specific copper rivet kit for wash-down and corrosive environments where full stainless fastener construction is required.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is in the package:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMatched fastener strips\u003c\/strong\u003e (stainless steel) sized for 54\" (1350mm) belt\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolid copper rivets\u003c\/strong\u003e (corrosion-resistant, non-sparking)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCopper burrs (washers)\u003c\/strong\u003e for distributing clinching load\u003c\/li\u003e\n\u003cli\u003eInstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eRequired installation hardware NOT included:\u003c\/strong\u003e rivet setter or punch, hammer, backing anvil, belt cutter or square. Sold separately.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy copper:\u003c\/strong\u003e Copper is naturally corrosion-resistant, clinches cleanly on fabric and rubber carcasses without cracking, and is non-sparking. This makes it the traditional and current choice for grain elevators, flour mills, and environments where ferrous sparks are unacceptable near dry crops or combustible dust. Copper burrs distribute clinching load across the belt surface, maintaining grip even on soft or worn belt covers.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMaterial combination:\u003c\/strong\u003e 316 stainless steel fastener strips paired with solid copper rivets and copper burrs. Stainless fastener with copper rivets combines corrosion resistance with non-sparking behavior for the most demanding wash-down and dust-hazard applications.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eApplications:\u003c\/strong\u003e Used in food processing wash-down lines with non-ferrous-only specifications, pharmaceutical manufacturing, chemical processing with dust-hazard requirements, and marine or coastal installations. Not recommended for heavy mining, quarry, cement, or high-PIW conveyors where Plategrip or Riv-Nail is the correct choice.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInstallation:\u003c\/strong\u003e Requires a rivet setter or punch, hammer, backing anvil, belt cutter or square, and optionally a rivet-setting press. Skill level is moderate. Technicians match rivet length to combined belt thickness plus burr, maintain consistent hole spacing, and avoid over-peening that would crack the burr or deform the belt.\u003c\/p\u003e\u003cp\u003eTexas Belting is an authorized MATO distributor shipping from Houston, TX. Same-day shipping on stocked items. Call 888-203-2358 for sizing help or bulk pricing.\u003c\/p\u003e","brand":"MATO","offers":[{"title":"Default Title","offer_id":46693269176509,"sku":"CR-AMS-54","price":132.7,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0666\/7721\/files\/cai-riv-nail-rivets-group_63e38a5a-69a6-4450-b02e-5eca62dfd868.jpg?v=1778107146"},{"product_id":"copper-rivet-fastener-cr-2a-24-fastener-set-24-600mm","title":"Copper Rivet CR-2A Complete Splice Kit - Steel Fasteners with Copper Rivets, 24\" (600mm) Belt Width","description":"\u003cp\u003e\u003cstrong\u003eCopper Rivet CR-2A Complete Splice Kit\u003c\/strong\u003e is a steel fastener and copper rivet belt splicing kit for a 24-inch (600mm) belt width. The kit contains matched fastener strips, solid copper rivets, copper burrs (washers), and installation instructions for a permanent clinched mechanical splice. CR-2A is MATO's light-duty copper rivet kit sized for smaller agricultural and industrial belts in the 12\" to 36\" width range.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is in the package:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMatched fastener strips\u003c\/strong\u003e (carbon steel) sized for 24\" (600mm) belt\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolid copper rivets\u003c\/strong\u003e (corrosion-resistant, non-sparking)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCopper burrs (washers)\u003c\/strong\u003e for distributing clinching load\u003c\/li\u003e\n\u003cli\u003eInstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eRequired installation hardware NOT included:\u003c\/strong\u003e rivet setter or punch, hammer, backing anvil, belt cutter or square. Sold separately.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy copper:\u003c\/strong\u003e Copper is naturally corrosion-resistant, clinches cleanly on fabric and rubber carcasses without cracking, and is non-sparking. This makes it the traditional and current choice for grain elevators, flour mills, and environments where ferrous sparks are unacceptable near dry crops or combustible dust. Copper burrs distribute clinching load across the belt surface, maintaining grip even on soft or worn belt covers.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMaterial combination:\u003c\/strong\u003e Steel fastener strips paired with solid copper rivets and copper burrs. Steel fastener with copper rivets is the standard economical combination for general agricultural and industrial service.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eApplications:\u003c\/strong\u003e Used in smaller baler belts, forage harvester belts, farm-equipment drive belts, flour mill conveyors requiring non-sparking hardware, and small-belt power transmission repair. Not recommended for heavy mining, quarry, cement, or high-PIW conveyors where Plategrip or Riv-Nail is the correct choice.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInstallation:\u003c\/strong\u003e Requires a rivet setter or punch, hammer, backing anvil, belt cutter or square, and optionally a rivet-setting press. Skill level is moderate. Technicians match rivet length to combined belt thickness plus burr, maintain consistent hole spacing, and avoid over-peening that would crack the burr or deform the belt.\u003c\/p\u003e\u003cp\u003eTexas Belting is an authorized MATO distributor shipping from Houston, TX. Same-day shipping on stocked items. Call 888-203-2358 for sizing help or bulk pricing.\u003c\/p\u003e","brand":"MATO","offers":[{"title":"Default Title","offer_id":46693269209277,"sku":"CR-2A-24","price":129.12,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0666\/7721\/files\/cai-riv-nail-rivets-group_fad9b5f2-1fa1-415c-a38d-74fc6c01c942.jpg?v=1778107087"},{"product_id":"copper-rivet-fastener-cr-2as-12-copper-rivet-12-ss","title":"Copper Rivet CR-2A Complete Splice Kit - 316 Stainless Fasteners with Copper Rivets, 12\" (300mm) Belt Width","description":"\u003cp\u003e\u003cstrong\u003eCopper Rivet CR-2A Complete Splice Kit\u003c\/strong\u003e is a stainless fastener and copper rivet belt splicing kit for a 12-inch (300mm) belt width. The kit contains matched fastener strips, solid copper rivets, copper burrs (washers), and installation instructions for a permanent clinched mechanical splice. CR-2A is MATO's light-duty copper rivet kit sized for smaller agricultural and industrial belts in the 12\" to 36\" width range.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is in the package:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMatched fastener strips\u003c\/strong\u003e (stainless steel) sized for 12\" (300mm) belt\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolid copper rivets\u003c\/strong\u003e (corrosion-resistant, non-sparking)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCopper burrs (washers)\u003c\/strong\u003e for distributing clinching load\u003c\/li\u003e\n\u003cli\u003eInstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eRequired installation hardware NOT included:\u003c\/strong\u003e rivet setter or punch, hammer, backing anvil, belt cutter or square. Sold separately.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy copper:\u003c\/strong\u003e Copper is naturally corrosion-resistant, clinches cleanly on fabric and rubber carcasses without cracking, and is non-sparking. This makes it the traditional and current choice for grain elevators, flour mills, and environments where ferrous sparks are unacceptable near dry crops or combustible dust. Copper burrs distribute clinching load across the belt surface, maintaining grip even on soft or worn belt covers.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMaterial combination:\u003c\/strong\u003e 316 stainless steel fastener strips paired with solid copper rivets and copper burrs. Stainless fastener with copper rivets combines corrosion resistance with non-sparking behavior for the most demanding wash-down and dust-hazard applications.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eApplications:\u003c\/strong\u003e Used in smaller baler belts, forage harvester belts, farm-equipment drive belts, flour mill conveyors requiring non-sparking hardware, and small-belt power transmission repair. Not recommended for heavy mining, quarry, cement, or high-PIW conveyors where Plategrip or Riv-Nail is the correct choice.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInstallation:\u003c\/strong\u003e Requires a rivet setter or punch, hammer, backing anvil, belt cutter or square, and optionally a rivet-setting press. Skill level is moderate. Technicians match rivet length to combined belt thickness plus burr, maintain consistent hole spacing, and avoid over-peening that would crack the burr or deform the belt.\u003c\/p\u003e\u003cp\u003eTexas Belting is an authorized MATO distributor shipping from Houston, TX. Same-day shipping on stocked items. Call 888-203-2358 for sizing help or bulk pricing.\u003c\/p\u003e","brand":"MATO","offers":[{"title":"Default Title","offer_id":46693269242045,"sku":"CR-2AS-12","price":115.28,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0666\/7721\/files\/cai-riv-nail-rivets-group_9d9b4f8e-6c3a-439f-a33a-0b44df28cd24.jpg?v=1778107087"},{"product_id":"copper-rivet-fastener-cr-2as-14-copper-rivet-14-ss","title":"Copper Rivet CR-2A Complete Splice Kit - 316 Stainless Fasteners with Copper Rivets, 14\" (350mm) Belt Width","description":"\u003cp\u003e\u003cstrong\u003eCopper Rivet CR-2A Complete Splice Kit\u003c\/strong\u003e is a stainless fastener and copper rivet belt splicing kit for a 14-inch (350mm) belt width. The kit contains matched fastener strips, solid copper rivets, copper burrs (washers), and installation instructions for a permanent clinched mechanical splice. CR-2A is MATO's light-duty copper rivet kit sized for smaller agricultural and industrial belts in the 12\" to 36\" width range.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is in the package:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMatched fastener strips\u003c\/strong\u003e (stainless steel) sized for 14\" (350mm) belt\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolid copper rivets\u003c\/strong\u003e (corrosion-resistant, non-sparking)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCopper burrs (washers)\u003c\/strong\u003e for distributing clinching load\u003c\/li\u003e\n\u003cli\u003eInstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eRequired installation hardware NOT included:\u003c\/strong\u003e rivet setter or punch, hammer, backing anvil, belt cutter or square. Sold separately.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy copper:\u003c\/strong\u003e Copper is naturally corrosion-resistant, clinches cleanly on fabric and rubber carcasses without cracking, and is non-sparking. This makes it the traditional and current choice for grain elevators, flour mills, and environments where ferrous sparks are unacceptable near dry crops or combustible dust. Copper burrs distribute clinching load across the belt surface, maintaining grip even on soft or worn belt covers.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMaterial combination:\u003c\/strong\u003e 316 stainless steel fastener strips paired with solid copper rivets and copper burrs. Stainless fastener with copper rivets combines corrosion resistance with non-sparking behavior for the most demanding wash-down and dust-hazard applications.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eApplications:\u003c\/strong\u003e Used in smaller baler belts, forage harvester belts, farm-equipment drive belts, flour mill conveyors requiring non-sparking hardware, and small-belt power transmission repair. Not recommended for heavy mining, quarry, cement, or high-PIW conveyors where Plategrip or Riv-Nail is the correct choice.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInstallation:\u003c\/strong\u003e Requires a rivet setter or punch, hammer, backing anvil, belt cutter or square, and optionally a rivet-setting press. Skill level is moderate. Technicians match rivet length to combined belt thickness plus burr, maintain consistent hole spacing, and avoid over-peening that would crack the burr or deform the belt.\u003c\/p\u003e\u003cp\u003eTexas Belting is an authorized MATO distributor shipping from Houston, TX. Same-day shipping on stocked items. Call 888-203-2358 for sizing help or bulk pricing.\u003c\/p\u003e","brand":"MATO","offers":[{"title":"Default Title","offer_id":46693269340349,"sku":"CR-2AS-14","price":134.49,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0666\/7721\/files\/cai-riv-nail-rivets-group_61b79b5a-442f-4b86-a35a-27d9fd84ff8c.jpg?v=1778107086"},{"product_id":"copper-rivet-fastener-cr-2as-24-copper-rivet-24-ss","title":"Copper Rivet CR-2A Complete Splice Kit - 316 Stainless Fasteners with Copper Rivets, 24\" (600mm) Belt Width","description":"\u003cp\u003e\u003cstrong\u003eCopper Rivet CR-2A Complete Splice Kit\u003c\/strong\u003e is a stainless fastener and copper rivet belt splicing kit for a 24-inch (600mm) belt width. The kit contains matched fastener strips, solid copper rivets, copper burrs (washers), and installation instructions for a permanent clinched mechanical splice. CR-2A is MATO's light-duty copper rivet kit sized for smaller agricultural and industrial belts in the 12\" to 36\" width range.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is in the package:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMatched fastener strips\u003c\/strong\u003e (stainless steel) sized for 24\" (600mm) belt\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolid copper rivets\u003c\/strong\u003e (corrosion-resistant, non-sparking)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCopper burrs (washers)\u003c\/strong\u003e for distributing clinching load\u003c\/li\u003e\n\u003cli\u003eInstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eRequired installation hardware NOT included:\u003c\/strong\u003e rivet setter or punch, hammer, backing anvil, belt cutter or square. Sold separately.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy copper:\u003c\/strong\u003e Copper is naturally corrosion-resistant, clinches cleanly on fabric and rubber carcasses without cracking, and is non-sparking. This makes it the traditional and current choice for grain elevators, flour mills, and environments where ferrous sparks are unacceptable near dry crops or combustible dust. Copper burrs distribute clinching load across the belt surface, maintaining grip even on soft or worn belt covers.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMaterial combination:\u003c\/strong\u003e 316 stainless steel fastener strips paired with solid copper rivets and copper burrs. Stainless fastener with copper rivets combines corrosion resistance with non-sparking behavior for the most demanding wash-down and dust-hazard applications.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eApplications:\u003c\/strong\u003e Used in smaller baler belts, forage harvester belts, farm-equipment drive belts, flour mill conveyors requiring non-sparking hardware, and small-belt power transmission repair. Not recommended for heavy mining, quarry, cement, or high-PIW conveyors where Plategrip or Riv-Nail is the correct choice.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInstallation:\u003c\/strong\u003e Requires a rivet setter or punch, hammer, backing anvil, belt cutter or square, and optionally a rivet-setting press. Skill level is moderate. Technicians match rivet length to combined belt thickness plus burr, maintain consistent hole spacing, and avoid over-peening that would crack the burr or deform the belt.\u003c\/p\u003e\u003cp\u003eTexas Belting is an authorized MATO distributor shipping from Houston, TX. Same-day shipping on stocked items. Call 888-203-2358 for sizing help or bulk pricing.\u003c\/p\u003e","brand":"MATO","offers":[{"title":"Default Title","offer_id":46693269536957,"sku":"CR-2AS-24","price":248.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0666\/7721\/files\/cai-riv-nail-rivets-group_e27cba3e-1897-49e7-9ae6-82b400ffe6da.jpg?v=1778107087"},{"product_id":"copper-rivet-fastener-cr-ams-32-ss-fastener-set","title":"Copper Rivet CR-AMS Complete Splice Kit - 316 Stainless Fasteners with Copper Rivets, 32\" (800mm) Belt Width","description":"\u003cp\u003e\u003cstrong\u003eCopper Rivet CR-AMS Complete Splice Kit\u003c\/strong\u003e is a stainless fastener and copper rivet belt splicing kit for a 32-inch (800mm) belt width. The kit contains matched fastener strips, solid copper rivets, copper burrs (washers), and installation instructions for a permanent clinched mechanical splice. CR-AMS is MATO's stainless-specific copper rivet kit for wash-down and corrosive environments where full stainless fastener construction is required.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is in the package:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMatched fastener strips\u003c\/strong\u003e (stainless steel) sized for 32\" (800mm) belt\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolid copper rivets\u003c\/strong\u003e (corrosion-resistant, non-sparking)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCopper burrs (washers)\u003c\/strong\u003e for distributing clinching load\u003c\/li\u003e\n\u003cli\u003eInstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eRequired installation hardware NOT included:\u003c\/strong\u003e rivet setter or punch, hammer, backing anvil, belt cutter or square. Sold separately.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy copper:\u003c\/strong\u003e Copper is naturally corrosion-resistant, clinches cleanly on fabric and rubber carcasses without cracking, and is non-sparking. This makes it the traditional and current choice for grain elevators, flour mills, and environments where ferrous sparks are unacceptable near dry crops or combustible dust. Copper burrs distribute clinching load across the belt surface, maintaining grip even on soft or worn belt covers.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMaterial combination:\u003c\/strong\u003e 316 stainless steel fastener strips paired with solid copper rivets and copper burrs. Stainless fastener with copper rivets combines corrosion resistance with non-sparking behavior for the most demanding wash-down and dust-hazard applications.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eApplications:\u003c\/strong\u003e Used in food processing wash-down lines with non-ferrous-only specifications, pharmaceutical manufacturing, chemical processing with dust-hazard requirements, and marine or coastal installations. Not recommended for heavy mining, quarry, cement, or high-PIW conveyors where Plategrip or Riv-Nail is the correct choice.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInstallation:\u003c\/strong\u003e Requires a rivet setter or punch, hammer, backing anvil, belt cutter or square, and optionally a rivet-setting press. Skill level is moderate. Technicians match rivet length to combined belt thickness plus burr, maintain consistent hole spacing, and avoid over-peening that would crack the burr or deform the belt.\u003c\/p\u003e\u003cp\u003eTexas Belting is an authorized MATO distributor shipping from Houston, TX. Same-day shipping on stocked items. Call 888-203-2358 for sizing help or bulk pricing.\u003c\/p\u003e","brand":"MATO","offers":[{"title":"Default Title","offer_id":46693269700797,"sku":"CR-AMS-32","price":96.65,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0666\/7721\/files\/cai-riv-nail-rivets-group_8595c622-e5ac-40bc-804a-906c07ff6c99.jpg?v=1778107087"},{"product_id":"copper-rivet-fastener-cr-super-a-24-stl-w-copper-rivets","title":"Copper Rivet CR-Super Complete Splice Kit - Steel Fasteners with Copper Rivets, 24\" (600mm) Belt Width","description":"\u003cp\u003e\u003cstrong\u003eCopper Rivet CR-Super Complete Splice Kit\u003c\/strong\u003e is a steel fastener and copper rivet belt splicing kit for a 24-inch (600mm) belt width. The kit contains matched fastener strips, solid copper rivets, copper burrs (washers), and installation instructions for a permanent clinched mechanical splice. CR-Super is MATO's primary copper rivet splice kit for rubber-and-fabric baler belts, canvas flat belts, and fabric-reinforced power transmission belts.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is in the package:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMatched fastener strips\u003c\/strong\u003e (carbon steel) sized for 24\" (600mm) belt\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolid copper rivets\u003c\/strong\u003e (corrosion-resistant, non-sparking)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCopper burrs (washers)\u003c\/strong\u003e for distributing clinching load\u003c\/li\u003e\n\u003cli\u003eInstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eRequired installation hardware NOT included:\u003c\/strong\u003e rivet setter or punch, hammer, backing anvil, belt cutter or square. Sold separately.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy copper:\u003c\/strong\u003e Copper is naturally corrosion-resistant, clinches cleanly on fabric and rubber carcasses without cracking, and is non-sparking. This makes it the traditional and current choice for grain elevators, flour mills, and environments where ferrous sparks are unacceptable near dry crops or combustible dust. Copper burrs distribute clinching load across the belt surface, maintaining grip even on soft or worn belt covers.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMaterial combination:\u003c\/strong\u003e Steel fastener strips paired with solid copper rivets and copper burrs. Steel fastener with copper rivets is the standard economical combination for general agricultural and industrial service.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eApplications:\u003c\/strong\u003e Used in round-baler belt splicing on John Deere, New Holland, and Vermeer equipment, grain elevator transfer belts, sawmill flat drive belt repair, and legacy power transmission applications. Not recommended for heavy mining, quarry, cement, or high-PIW conveyors where Plategrip or Riv-Nail is the correct choice.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInstallation:\u003c\/strong\u003e Requires a rivet setter or punch, hammer, backing anvil, belt cutter or square, and optionally a rivet-setting press. Skill level is moderate. Technicians match rivet length to combined belt thickness plus burr, maintain consistent hole spacing, and avoid over-peening that would crack the burr or deform the belt.\u003c\/p\u003e\u003cp\u003eTexas Belting is an authorized MATO distributor shipping from Houston, TX. Same-day shipping on stocked items. Call 888-203-2358 for sizing help or bulk pricing.\u003c\/p\u003e","brand":"MATO","offers":[{"title":"Default Title","offer_id":46693270192317,"sku":"CR-Super A-24","price":160.92,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0666\/7721\/files\/cai-riv-nail-rivets-group_9520bb24-bd95-4156-8fd2-ac43b91a8e2f.jpg?v=1778107086"},{"product_id":"copper-rivet-fastener-cr-super-as-72-ss-w-copper-rivets","title":"Copper Rivet CR-Super Complete Splice Kit - 316 Stainless Fasteners with Copper Rivets, 72\" (1800mm) Belt Width","description":"\u003cp\u003e\u003cstrong\u003eCopper Rivet CR-Super Complete Splice Kit\u003c\/strong\u003e is a stainless fastener and copper rivet belt splicing kit for a 72-inch (1800mm) belt width. The kit contains matched fastener strips, solid copper rivets, copper burrs (washers), and installation instructions for a permanent clinched mechanical splice. CR-Super is MATO's primary copper rivet splice kit for rubber-and-fabric baler belts, canvas flat belts, and fabric-reinforced power transmission belts.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhat is in the package:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMatched fastener strips\u003c\/strong\u003e (stainless steel) sized for 72\" (1800mm) belt\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolid copper rivets\u003c\/strong\u003e (corrosion-resistant, non-sparking)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCopper burrs (washers)\u003c\/strong\u003e for distributing clinching load\u003c\/li\u003e\n\u003cli\u003eInstallation instructions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eRequired installation hardware NOT included:\u003c\/strong\u003e rivet setter or punch, hammer, backing anvil, belt cutter or square. Sold separately.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eWhy copper:\u003c\/strong\u003e Copper is naturally corrosion-resistant, clinches cleanly on fabric and rubber carcasses without cracking, and is non-sparking. This makes it the traditional and current choice for grain elevators, flour mills, and environments where ferrous sparks are unacceptable near dry crops or combustible dust. Copper burrs distribute clinching load across the belt surface, maintaining grip even on soft or worn belt covers.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eMaterial combination:\u003c\/strong\u003e 316 stainless steel fastener strips paired with solid copper rivets and copper burrs. Stainless fastener with copper rivets combines corrosion resistance with non-sparking behavior for the most demanding wash-down and dust-hazard applications.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eApplications:\u003c\/strong\u003e Used in round-baler belt splicing on John Deere, New Holland, and Vermeer equipment, grain elevator transfer belts, sawmill flat drive belt repair, and legacy power transmission applications. Not recommended for heavy mining, quarry, cement, or high-PIW conveyors where Plategrip or Riv-Nail is the correct choice.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eInstallation:\u003c\/strong\u003e Requires a rivet setter or punch, hammer, backing anvil, belt cutter or square, and optionally a rivet-setting press. Skill level is moderate. Technicians match rivet length to combined belt thickness plus burr, maintain consistent hole spacing, and avoid over-peening that would crack the burr or deform the belt.\u003c\/p\u003e\u003cp\u003eTexas Belting is an authorized MATO distributor shipping from Houston, TX. Same-day shipping on stocked items. Call 888-203-2358 for sizing help or bulk pricing.\u003c\/p\u003e","brand":"MATO","offers":[{"title":"Default Title","offer_id":46693270585533,"sku":"CR-Super AS-72","price":925.63,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0666\/7721\/files\/cai-riv-nail-rivets-group_40736a9e-5483-4a8e-92ad-1f235ffc62c9.jpg?v=1778107026"}],"url":"https:\/\/texasbelting.com\/collections\/copper-rivet-fasteners.oembed","provider":"Texas Belting and Supply","version":"1.0","type":"link"}